Questions? Our offices are closed for another 7.5 hours.Toll-free at (800)777-6405 (U.S. and Canada) or (408)738-3959 (Click Here To Email Us)
The Original and World's Finest Aircraft Covers for Airplanes, Jets, Helicopters, Gliders and QEC Off-link Jet Engines
Sikorsky S-92 Windshield/Nose Cover (illustration)
Check out our Cold Weather Products in the list just below.
Protect your airplane from ice, snow and freezing temperatures with Insulated Engine Covers, Wing Covers and more!
close= Bruce's Comments, Photos, Info & More.= Product Photos, Etc.= Items that have expedited delivery.
INSULATED ROTOR HUB COVER
Rotor Hub Covers overlaps with the Blade Covers to ensure complete protection for the entire main rotor system. Designed like a jacket with sleeves and no collar, the rotor hub cover fastens together below each blade with Delrin buckles. The Rotor Hub Cover is normally made from Solution-Dyed Polyester.... read more
BLADE COVERS (cold weather type) (set of 4)
The Sikorsky S92, CH-148 Cyclone Blade Covers are sewn of medium weight Solution-Dyed Polyester. Cut "full" to avoid trim tabs, Blade Covers can be installed from the ground with the aid of lightweight rope which is attached to the open end. Covers are cinched tight at the blade root with straps and quick-release plastic buckles. A small opening at the tip of the cover allows for some air circulation and drainage. For operations in extremely cold weather, the Cold Weather Blade Covers are fitted with full length zippers, and with optional "boots" designed to accept a preheater hose.... read more
Only want to see some of our products?
Use the Product Filter Checkbox List to
only see the products that interest you.
The Sikorsky S92, CH-148 Cyclone Windshield/Nose Cover is designed to cover the windshield and side windows of the cockpit, and extends forward to cover the nose.
Sorry, no photos at this time.
Check out the photo gallery or contact Bruce about this product.
ENGINE INTAKE/EXHAUST COVER SET (set of 4)
Engine Cover details vary by model, but generally these covers are designed to enclose and protect the swash plate, inlet, exhaust and engine access areas. They are designed to tighten up around the main rotor drive shaft and tailboom bottleneck areas, and attach securely with straps either under the belly or to the land gear cross tubes (or both). Delrin buckles are used to tighten the attachment straps. The engine cover is made of Solution-Dyed Polyester or acrylic Sunbrella, and is available in a variety of colors (contact us for details. Specific information for each model is available on request.... read more
ROTOR HUB COVER
TAIL ROTOR BLADE COVERS (set of 4)
The Sikorsky S92, CH-148 Cyclone Tail Rotor Cover is a one-piece design which encloses both the blades and their hub, snapping closed along the bottom edge. The tail rotor cover is normally made from Solution-Dyed Polyester.... read more
TAIL ROTOR HUB COVER
PITOT COVERS (set of 3)
Pitot Tube Covers, made of Naugahyde vinyl, are designed to cover the entire pitot assembly. Slipping on over the tube, the cover tightens around the base with a special Velcro strap detail. A "Remove Before Flight" streamer is attached to the cover. Heat Resistant Pitot Covers are designed to withstand more than 500Â° Fahrenheit, and will prevent the pitot cover from melting onto the tube if the pitot heat is accidentally turned on with the pitot cover attached.... read more
PITOT COVERS, heat resistant type (set of 3)
Our heat resistant Pitot covers are lined with fireproof Nomex to prevent burn stains on the Pitot tube if the Pitot heat is activated while on the ground during maintenance procedures. Â The Nomex will NOT prevent the Pitot cover from being damaged by the heat, which can be as high as 500 degrees F. (260 degrees C.), but it will prevent unsightly burn stains on the Pitot tube which cannot be removed.... read more
PITOT COVERS (Covers Stand-Off) (set of 3)
PITOT COVERS, heat resistant type (Covers Stand-Off) (set of 3)
COCKPIT HEATSHIELD SET (set of 8)
Heatshield Interior Reflectors are made of a special laminate of metallized polyester film and closed cell foam. Less than 1/8" thick, the Reflector can fold up flat and store in a sleeve, yet is stiff enough when flat to stand up against the windshield using the sun visors and window framing only. On some designs no Velcro or suction cups are necessary. Heatshields are an excellent short-term remedy for cockpit overheating, but use the Bubble Cover for more effective and practical long term protection.... read more
WHEEL COVERS (set of 3)
Wheel or Wheelpant Covers are designed to protect the wheelpants, or the wheel and tires, from sun damage and damage from the tow bar when moving the airplane.
INSTRUMENT PANEL/CENTER CONSOLE COVER
MAIN LANDING GEAR HANDLE COVER
TRAVEL COVER, Light Weight Travel Windshield/Nose Cover
TRAVEL COVER, Light Weight Travel Bubble Cover
Can't find what you're looking for? We probably make it! Our offices are currently closed for Our offices are closed for another 7.5 hours.. Send an email to firstname.lastname@example.org with information about your aircraft and the product you are looking for!
photo credit: Bruce's Custom Covers, Aircraft Covers, Inc.Bruce's Custom Covers, Aircraft Covers, Inc.
photo credit: Photo provided by customerPhoto provided by customer
CLICK on any small image to enlarge it or CLICK on arrows to view next image
general aviation > helicopters | gyrocopters