Questions? We're open! Call now: toll-free at (800)777-6405 (U.S. and Canada) or (408)738-3959 -- Talk to one of our representatives:
Kevin, Pegi, Tayler, Javier or Ivan
The Original and World's Finest Aircraft Covers for Airplanes, Jets, Helicopters, Gliders and QEC Off-link Jet Engines
MD520 NOTAR Bubble, Engine, & NOTAR Covers & Blade Tie-downs
Check out our Cold Weather Products in the list just below.
Protect your airplane from ice, snow and freezing temperatures with Insulated Engine Covers, Wing Covers and more!
close= Bruce's Comments, Photos, Info & More.= Product Photos, Etc.= Items that have expedited delivery.
BLADE COVERS (COLD WEATHER TYPE) (set of 5)
The McDonnell Douglas MDD 520 Notar Blade Covers are sewn of medium weight Solution-Dyed Polyester. Cut "full" to avoid trim tabs, Blade Covers can be installed from the ground with the aid of lightweight rope which is attached to the open end. Covers are cinched tight at the blade root with straps and quick-release plastic buckles. A small opening at the tip of the cover allows for some air circulation and drainage. For operations in extremely cold weather, the Cold Weather Blade Covers are fitted with full length zippers, and with optional "boots" designed to accept a preheater hose.... read more
Only want to see some of our products?
Use the Product Filter Checkbox List to
only see the products that interest you.
The McDonnell Douglas MDD 520 Notar Bubble Cover helps reduce damage to the upholstery and avionics caused by excessive heat and can eliminate problems caused by leaking door and window seals. They keep the windshield and window surfaces clean and help prevent vandalism and theft.... read more
The Bubble Cover encloses the entire canopy including the windshield, skylights, and chin bubble Attachment buckles are made of nonmetal Delrin, designed for rugged outdoor use. Both the top and bottom hems of the cover have a special rope-hem feature with which they can be tightened to help prevent abrasive chafing of the windshield. Pockets are sewn into the cover for the temperature probe and pitot tubes. The bubble cover is reinforced with patches at hinge points, door handles, and for the windshield wipers. For ease of installation, the bubble cover is color-coded (red=left, green=right) with color swatches sewn into the corners.... read more
Each Bubble Cover is normally made from Silver Acrylic Sunbrella or Silver Solution-Dyed Polyester and is lined 100% with a soft and smooth microfiber. Bruce's Custom Covers developed this material combination especially for aircraft protection. The outer material is medium weight and treated for water resistance, UV resistance and anti-static buildup. The inner lining is a very soft and smooth microfiber to prevent scratching. The materials are extremely UV reflective, and tests show that the cabin interior temperature can be reduced to near-ambient temperature on even the hottest of days. It is water, ice and snow repellent, yet breathable enough to allow moisture to escape from between the cover and the aircraft surface. Our materials do not contain hydrocarbon compounds that can harm Plexiglas windshields and acrylic finishes. Other colors are available. Please contact us for availability and price. We also have an ultra lightweight material available for fitted hangar dust covers.... read more
BUBBLE COVER WITH WIRE STRIKE DETAIL
BUBBLE COVER WITH INTAKE COVER ADD-ON
ROTOR HUB/DOGHOUSE COVER (blades removed)
Rotor Hub Covers overlaps with the Blade Covers to ensure complete protection for the entire main rotor system. Designed like a jacket with sleeves and no collar, the rotor hub cover fastens together below each blade with Delrin buckles. The Rotor Hub Cover is normally made from Solution-Dyed Polyester.... read more
Sorry, no photos at this time.
Check out the photo gallery or contact Bruce about this product.
DOGHOUSE/MAIN INTAKE COVER
The McDonnell Douglas MDD 520 Notar Intake Cover. Details vary by model, but generally helicopter intake covers are designed to enclose the intake are only. They are smaller than helicopter engine covers, and their attachment details can vary from straps, to snaps, or some combination of the two. Specific information for each model is available on request.... read more
DOGHOUSE/MAIN INTAKE/ENGINE AREA COVER (non a/c models)
Engine Cover details vary by model, but generally these covers are designed to enclose and protect the swash plate, inlet, exhaust and engine access areas. They are designed to tighten up around the main rotor drive shaft and tailboom bottleneck areas, and attach securely with straps either under the belly or to the land gear cross tubes (or both). Delrin buckles are used to tighten the attachment straps. The engine cover is made of Solution-Dyed Polyester or acrylic Sunbrella, and is available in a variety of colors (contact us for details. Specific information for each model is available on request.... read more
BLADE COVERS (set of 5)
ROTOR HUB COVER
BLADE TIE-DOWNS (set of 5)
Blade Tie-Downs are "socks" which fit over the blade tip with or without Blade Covers installed. Front blade tie-downs have two lengths of rope or strap which attaches to the front cross tubes on either side of the cabin. The other tie-downs have generous lengths of rope or strap to tie the blades down at any convenient spot.... read more
NOTAR THRUSTER COVER
The Tailboom Cover details vary by model, but generally the helicopter tail boom cover encloses the tail boom from the "bottleneck" to the aft end. They usually also cover the horizontal stabilizers, and are custom made to allow for antennae, lights, and other protrusions. They attach with straps underneath the tail boom. Covers for the vertical and horizontal stabilizers are also available separately. Specific information for each model is available on request.... read more
HORIZONTAL STABILIZER COVER
PROTECTIVE BAGS FOR REMOVABLE AFT DOORS, padded (set of 2)
**Padded Door Bags* are designed to provide portable protection of the doors when they are removed from the aircraft. They are padded to moderate thickness, zippered closed, and have sturdy carry handles for easy transport.... read more
PROTECTIVE BAGS FOR REMOVABLE FWD DOORS, padded (set of 2)
TRAVEL COVER, Light Weight Travel Bubble Cover
The McDonnell Douglas MDD 520 Notar Lightweight Travel Bubble Cover is the same design as our standard bubble cover, but the material used is very lightwieight and will fold up and store in a smaller space.... read more
NOTE: To preserve their light weight, Travel Covers have a soft lining in selected areas only.
TRAVEL COVER, Light Weight Travel Bubble Cover WITH WIRE STRIKE DETAIL
TRAVEL COVER, Light Weight Travel Bubble Cover WITH INTAKE COVER ADD-ON
Can't find what you're looking for? We probably make it! Call us at (408)738-3959 or toll-free at (800)777-6405 (U.S. & Canada) Or use our online contact form here.
photo credit: Photo provided by customerPhoto provided by customer
photo credit: Bruce's Custom Covers, Aircraft Covers, Inc.Bruce's Custom Covers, Aircraft Covers, Inc.
CLICK on any small image to enlarge it or CLICK on arrows to view next image
general aviation > helicopters | gyrocopters