Questions? We're open! Call now: toll-free at (800)777-6405 (U.S. and Canada) or (408)738-3959 -- Talk to one of our representatives:
Kevin, Pegi, Tayler, Javier or Ivan
The Original and World's Finest Aircraft Covers for Airplanes, Jets, Helicopters, Gliders and QEC Off-link Jet Engines
Bell 204 UH-1 Cockpit Cover
AVAILABLE NOW, your Oshkosh discount!
Hello from Oshkosh! Shop now for air show savings.
close= Bruce's Comments, Photos, Info & More.= Product Photos, Etc.= Items that have expedited delivery.
Only want to see some of our products?
Use the Product Filter Checkbox List to
only see the products that interest you.
FORWARD CABIN COVER
The Bell 204 & UH-1 Huey Forward Cabin Cover is designed to cover the front and side windows of the cockpit.
This cover type is made from Silver Acrylic Sunbrella canvas and is 100% lined with a soft and smooth microfiber. Bruce's Custom Covers developed this material combination especially for aircraft protection. The outer material is medium weight and treated for water resistance, UV resistance and anti-static buildup. The inner lining is a very soft and smooth microfiber to prevent scratching. The material is very reflective, and tests show that the cabin interior temperature can be reduced to near-ambient temperature on the hottest of days. It is water, ice and snow repellent, yet breathable to allow moisture to escape from between the cover and the aircraft surface.... read more
FORWARD CABIN/NOSE COVER
The Bell 204 & UH-1 Huey Forward Cabin/Nose Cover is designed to cover the front and side windows of the cockpit, and extend forward to cover the nose. Pockets are sewn into the cover to accommodate for the pitot tubes.... read more
FULL BODY COVER, including underbelly, for indoor storage only
Sorry, no photos at this time.
Check out the photo gallery or contact Bruce about this product.
ENGINE AREA/MID-CABIN COVER
Engine Cover details vary by model, but generally these covers are designed to enclose and protect the swash plate, inlet, exhaust and engine access areas. They are designed to tighten up around the main rotor drive shaft and tailboom bottleneck areas, and attach securely with straps either under the belly or to the land gear cross tubes (or both). Delrin buckles are used to tighten the attachment straps. The engine cover is made of Solution-Dyed Polyester or acrylic Sunbrella, and is available in a variety of colors (contact us for details. Specific information for each model is available on request.... read more
ALL-YEAR USE MATERIAL - Made with Silver Acrylic Sunbrella canvas, the all-year use material is the best option for sun protection and cover longevity. This heavier more durable material is intended for all weather conditions, such as rain and snow or lots of sun.... read more
WINTER USE MATERIAL - Made with Solution-Dyed Polyester fabric, this option is intended for seasonal use to aid in deicing, rain mitigation, or for occasional travel. The material is lighter and more compact, but more susceptible to UV damage and may have a shorter useful life if used continuously outside than the all-year use material.... read more
ENGINE AREA/MID-CABIN COVER, extends down to crosstubes
ENGINE AREA/MID-CABIN COVER, w/IR suppressor exhaust
INSULATED ENGINE AREA/MID-CABIN COVER
The Bell 204 & UH-1 Huey Insulated Engine Cover is made with a thicker, quilted, water-repellent, and breathable material that is insulated on the inside. The Insulated Engine Cover works well in cold climates to help with engine preheating.... read more
Insulated Covers Material - A special composite material of solution-dyed polyester, 3M Thinsulate insulation, and soft nylon interior fabric. Our insulated covers are designed to complement an engine preheater and help retain heat in the engine compartment after shutdown. If you operate your aircraft in cold-weather, these covers will help prevent engine wear and tear.... read more
INSULATED ENGINE AREA/MID-CABIN COVER, extends down to crosstubes
ENGINE EXHAUST COVER
AFT ENGINE COVER (overlaps with mid-cabin cover)
PARTICLE SEPARATOR INLET COVER (chain weighted type)
The Bell 204 & UH-1 Huey Intake Cover. Details vary by model, but generally helicopter intake covers are designed to enclose the intake are only. They are smaller than helicopter engine covers, and their attachment details can vary from straps, to snaps, or some combination of the two. Specific information for each model is available on request.... read more
ROTOR HUB/MAST COVER
Rotor Hub Covers overlaps with the Blade Covers to ensure complete protection for the entire main rotor system. Designed like a jacket with sleeves and no collar, the rotor hub cover fastens together below each blade with Delrin buckles. The Rotor Hub Cover is normally made from Solution-Dyed Polyester.... read more
BLADE COVERS, original 204 blades (set of 2)
The Bell 204 & UH-1 Huey Blade Covers are sewn of medium weight Solution-Dyed Polyester. Cut "full" to avoid trim tabs, Blade Covers can be installed from the ground with the aid of lightweight rope which is attached to the open end. Covers are cinched tight at the blade root with straps and quick-release plastic buckles. A small opening at the tip of the cover allows for some air circulation and drainage. For operations in extremely cold weather, the Cold Weather Blade Covers are fitted with full length zippers, and with optional "boots" designed to accept a preheater hose.... read more
BLADE COVERS, 205 model blades (set of 2)
BLADE COVERS (COLD WEATHER TYPE), original 204 blades (set of 2)
BLADE COVERS (COLD WEATHER TYPE), 205 model blades (set of 2)
BLADE COVERS, Padded For Hail Protection (set of 2)
HAIL PROTECTION COVERS: GENERAL DESCRIPTION
Hail Protection Covers are designed to effectively protect against small to moderate sized hailstones, yet still be practical enough to be somewhat portable and installable by 1-2 people. Upper surfaces are protected by 1/4" closed cell foam, sandwiched between fabric layers. .... read more
NOTE: This design is unlikely to protect against the largest hailstones, which can be larger than 1 inch in diameter.
FRONT BLADE TIE-DOWN
Blade Tie-Downs are "socks" which fit over the blade tip with or without Blade Covers installed. Front blade tie-downs have two lengths of rope or strap which attaches to the front cross tubes on either side of the cabin. The other tie-downs have generous lengths of rope or strap to tie the blades down at any convenient spot.... read more
REAR BLADE TIE-DOWN
BLADE TIE-DOWNS, FRONT & REAR (set of 2)
TAIL ROTOR COVER
The Bell 204 & UH-1 Huey Tail Rotor Cover is a one-piece design which encloses both the blades and their hub, snapping closed along the bottom edge. The tail rotor cover is normally made from Solution-Dyed Polyester.... read more
TAIL ROTOR HUB/GEARBOX COVER
TAIL ROTOR TIE-DOWNS (set of 2)
Tail Rotor Tie-Downs are a similar design to the main blade tie-downs. Stout bungee cords attached to the tie-down socks pull the rotor tips back toward the hub, pulling the tail rotor back to a secure position.... read more
PITOT COVERS (set of 2)
Pitot Tube Covers, made of Naugahyde vinyl, are designed to cover the entire pitot assembly. Slipping on over the tube, the cover tightens around the base with a special Velcro strap detail. A "Remove Before Flight" streamer is attached to the cover. Heat Resistant Pitot Covers are designed to withstand more than 500Â° Fahrenheit, and will prevent the pitot cover from melting onto the tube if the pitot heat is accidentally turned on with the pitot cover attached.... read more
STABILIZER BAR COVERS (set of 2)
HORIZONTAL STABILIZER COVERS (set of 2)
TAILBOOM COVER, indoor storage only
The Tailboom Cover details vary by model, but generally the helicopter tail boom cover encloses the tail boom from the "bottleneck" to the aft end. They usually also cover the horizontal stabilizers, and are custom made to allow for antennae, lights, and other protrusions. They attach with straps underneath the tail boom. Covers for the vertical and horizontal stabilizers are also available separately. Specific information for each model is available on request.... read more
COCKPIT HEATSHIELD SET (set of 8)
Heatshield Interior Reflectors are made of a special laminate of metallized polyester film and closed cell foam. Less than 1/8" thick, the Reflector can fold up flat and store in a sleeve, yet is stiff enough when flat to stand up against the windshield using the sun visors and window framing only. On some designs no Velcro or suction cups are necessary. Heatshields are an excellent short-term remedy for cockpit overheating, but use the Bubble Cover for more effective and practical long term protection.... read more
TRAVEL COVER, Light Weight Travel Forward Cabin Cover
TRAVEL COVER, Light Weight Travel Forward Cabin/Nose Cover
Can't find what you're looking for? We probably make it! Call us at (408)738-3959 or toll-free at (800)777-6405 (U.S. & Canada) Or use our online contact form here.
photo credit: Photo provided by customerPhoto provided by customer
photo credit: Bruce's Custom Covers, Aircraft Covers, Inc.Bruce's Custom Covers, Aircraft Covers, Inc.
CLICK on any small image to enlarge it or CLICK on arrows to view next image
general aviation > helicopters | gyrocopters