To Price List Download a printable version and order form Download a printable version and order form
 
Bruce's Custom Covers Technical Sheet
Bellanca Decathlon
 
Over-the-Top Canopy Cover
 

Canopy covers help reduce damage to your airplane's upholstery and avionics caused by excessive heat, and they can eliminate problems caused by leaky door and window seals. They keep the windshield and window surfaces clean and help prevent vandalism and theft.

The Decathlon Over-Top Canopy Cover encloses the windshield, side, and skylight windows. This is a one-piece design which wraps around the canopy and closes with Velcro behind the pilot's side door, and at the same place on the other side of the cabin. By peeling open the Velcro closure on the door side, one can enter the airplane without removing the entire cover. Over the top of the cabin area the cover extends out past the wing root fairings to help protect against leaks. The cover fastens with two belly straps which are adjustable and detachable from either side with heavy duty plastic buckles. To keep the sides of the cover from sagging, special tightening straps are sewn onto the upper hem on each side. To insure the most secure fit, high quality bungee cord is enclosed in the hem of the cover. This cord is also adjustable for tightness.

Each canopy cover is made of nylon Silver Laminate. Bruce's Custom Covers developed Silver Laminate especially for aircraft protection. The outer material is a medium weight nylon treated for ultraviolet resistance and anti-static buildup. The inner lining is brushed nylon tricot knit. Silver Laminate is extremely reflective. Tests show that the cabin interior temperature can be reduced by as much as 25 degrees F. It is water, ice and snow repellent, yet it is breathable enough to allow moisture to escape from between the cover and the windshield surface. Silver Laminate contains no hydrocarbon compounds which can harm plexiglass windshields and acrylic finishes.

Each canopy cover is custom sewn and trimmed in the colors of the airplane. A duffle bag is included with each cover. For an extra charge the airplane's registration number can be imprinted onto both sides of the cover.

Engine Inlet Plugs are "pillows" sewn of heavy duty vinyl material and stuffed with a single block of urethane foam. A zipper in the back of each plug allows the foam to be removed and dried if necessary. Engine plugs have warning flags which stick up above the cowl line, visible from the cockpit. Most plugs are embroidered with the aircraft registration number, done in black, about 1" high.

The Engine Cover is made of Silver Laminate like the Canopy Cover. It encloses the entire engine cowling area and closes with Velcro beneath the prop spinner. It is attached with a belly strap aft of the firewall, and with Velcro to the Canopy Cover.

The Propellor Cover is a one-piece form fit design which slips over the blades and spinner. The cover zips together along the bottom edge of the blade covers. The Propellor Cover is made of Silver Laminate.

Wing Covers and Horizontal Stabilizer Covers are form-fit to slip over the wing tip and secure with straps under the wing. Wing Covers are made of medium weight nylon, and come with a storage bag.

The Empennage Cover is a one-piece cover made to cover the vertical and horizontal stabilizers, as well as the tail area aft of the Canopy Cover. The cover attaches with Velcro to the aft edge of the Canopy Cover, and with straps underneath the belly. The cover is pulled back over the vertical stabilizer and a zipper is closed at the trailing edge of the rudder. The cover is then stretched over the elevators and zippered closed along the bottom elevator surfaces. There are also some straps under the elevators. The Empennage Cover is made of medium weight nylon.

HeatShield Interior Reflectors are made of a special laminate of metallized polyester film and closed cell foam. Less than 1/8" thick, the reflector is stiff enough when flat to stand up against the windshield using the sunvisors and window framing only. On some designs Velcro fasteners are necessary. HeatShields roll up and store in a sleeve, yet retain a memory to be flat whenever they are needed. HeatShields are an excellent short-term remedy for cockpit overheating, but the Canopy Cover offers a more effective and practical solution.

 
Over-the-Top Canopy Cover, aft view
 
Over-Top Canopy Cover, Extended to Tail, Propellor Cover, & Engine Cover
 
Over-Top Canopy, extended to cover gas caps
 
Over-Top Canopy Cover, Extended to Tail, Engine & Wing Covers
 
Propellor & Engine Covers
 
Back to Top
 
 Model+   Product Name   Price   Buy Now 
 BDEC-010  CANOPY COVER, STANDARD STYLE, BELLY STRAP TYPE  $395.00 
 BDEC-011  CANOPY COVER, OVER THE TOP STYLE, BELLY STRAP TYPE  $455.00 
 BDEC-020  CANOPY COVER, OVER TOP TYPE WITH EXT. TO TAIL, BELLY STRAP TYPE  $545.00 
 BDEC-100  ENGINE PLUGS  $95.00 
 BDEC-110  ENGINE COVER  $295.00 
 BDEC-120  PROPELLOR COVER, 2 blade  $185.00 
 BDEC-130  PROPELLOR COVER, 3 blade  $245.00 
 BDEC-200  WING COVERS  $425.00 
 BDEC-201  WING COVERS (Silver Laminate)  $510.00 
 BDEC-210  HORIZONTAL STABILIZER COVERS  $245.00 
 BDEC-215  EMPENNAGE COVER (overlaps with extended Canopy Cover)  $575.00 
 BDEC-216  WHEELPANT COVERS  $125.00 
 BDEC-217  WINGTIP & HORIZ. STAB. PADS  $365.00 
 BDEC-218  VERTICAL STABILIZER COVER  $125.00 
 BDEC-219  EMPENNAGE COVER (Silver Laminate, overlaps with extended Canopy Cover)  $690.00 
 BDEC-220  EMPENNAGE COVER, extends forward to wing trailing edge  $575.00 
 BDEC-300  WHEELPANT COVERS  $160.00 
 BDEC-905  WINDSHIELD HEATSHIELD  $65.00 
 BDEC-906  WINDSHIELD HEATSHIELD  $110.00 
 BDEC-915  HEATSHIELD SET (WITH SKYLIGHT)  $205.00