OH58-025: WINDSHIELD/NOSE COVER The OH58D Windshield/Nose Cover encloses the entire canopy including the windshield, skylights, chin bubble, front doors and windows. The cover attaches at 4 points. A strap at each upper rear corner attaches to the support tube inside the engine access doors. A strap at each lower rear corner attaches to the rear cross-tube. Attachment buckles are made of non-metal Delrin, designed for rugged outdoor use. Both the top and bottom hems of the cover have a special rope-hem feature with which they can be tightened to insure against wind-blown chaffing. Pockets are sewn into the cover for both the temperature probe and pitot tube. For ease of installation, bubble covers are color-coded (red=left, green=right) with color swatches sewn into the corners. This cover is made of nylon Silver Laminat, developed especially for aircraft protection. The outer material is a medium weight nylon treated for ultraviolet resistance and anti-static buildup. The inner lining is smooth-brushed nylon tricot knit. Silver Laminate is extremely reflective. Tests show that the cabin interior temperature can be reduced by as much as 25 degrees. It is water, ice and snow repellent, yet it is breathable enough to allow moisture to escape from between the cover and the windshield surface. Silver Laminate contains no hydrocarbon compounds which can harm plexiglass windshields and acrylic finishes.

OH58-500: TAIL ROTOR COVER The Tail Rotor Cover is a one-piece design which fits over the blades and hub, fastening with snaps along its bottom edge. Made of medium weight nylon, tabs have been sewn into the tips of the cover so that it may be tied down in high winds.

OH58-200: ROTOR MAST ANTENNA COVER The Rotor Mast Antenna Cover is designed to fit around the entire antenna structure, and tighten with straps along the aft edge. This cover is made of medium weight nylon, and is reinforced at the high-wear areas.

50 CAL, HELLFIRE, ROCKET & ALQ-144 COUNTERMEASURES COVERS These covers are designed to fit over the major structure of each weapon as they are mounted on the aircraft. Where necessary, more practical or requested, smaller covers are provided to enclose additional components such as magazine clips

CUSTOM IMPRINTING & EMBROIDERING Squadron insignias and aircraft numbers can be imprinted (silkscreened) or embroidered onto each cover. Insignia artwork can be submitted by mail, fax or e-mail (any graphic format).

Principal cover material (Silver Laminate) conforms to, or surpasses, all of the following specifications:

¥ CCC-A-680a (Federal Standard 191A Test Method 5903) ¥ Federal Automotive Upholstery Requirement MVSS-302 ¥ BIFMA (Screen Test-Sec. 3.3.1) Voluntary Std. ¥ Oil and mildew resistant as per CCC-A-680a ¥ Anti-static slip finish ¥ -20 degrees cold crack ¥ Wyzenbeek abrasion test (Federal Standard 191A, Method 5304)

1000 Denier Cordura nylon conforms to, or surpasses, all of the following specifications: ¥ CCC-A-680a (Federal Standard 191A Test Method 5903) ¥ Federal Automotive Upholstery Requirement MVSS-302 ¥ BIFMA (Screen Test-Sec. 3.3.1) Voluntary Std. ¥ Oil and mildew resistant as per CCC-A-680a ¥ Anti-static slip finish ¥ -20 degrees cold crack ¥ Wyzenbeek abrasion test (Federal Standard 191A, Method 5304)

Webbing attachment straps conform to, or surpasses the following specification: ¥ TYPE 17 MIL-W 4088 ¥ Width: 1.5" ¥ Color spec: 090 Black ¥ Breaking strength: 3,800 lbs. ¥ Thickness: .065"

All thread used conforms to the following specifications: ¥ Standard Spec. B-92 (16), Tex 70, 2003 Scarlet ¥ Standard Spec. B-92 (16), Tex 70, 53205 Black

Where requested, squadron emblems, logos and aircraft numbers can be silkscreened onto the cover. Silkscreening method conforms to the following test method and specifications: ¥ BIFMA (Screen Test-Sec. 3.3.1) Voluntary Std. ¥ Ink: manufacturer's spec MP-111 Black or MP-112 White ¥ General Test Method for silkscreened ink adhesion "Dime Scratch" type.

Where requested, aircraft numbers may be embroidered onto each cover, using the following specifications: ¥ Sans Seriph, German Block Type, 10 degrees italicized. ¥ Thread: TKT. 40, Tex. 27, SCYY, Col. B1720 White